lift supposed to move??

[outtyhere]

i got a lift kit on the front of my outty 800 is it supposed to move?
it wingles around .

also i didnt understand what to do with the washers that came with. i thought they were to go on the outside but only one fit on.

please help me out guys- im new to lift kits and how they are to be mounted.

thanks!!

[stricker76]

I'm not familiar with the outty lift, i'm sure someone who knows will chime in shortly. But, Welcome to the forum!

[racer37l]

Welcome to the insanity!! What year is your bike? And do you have a RDC lift kit? If so, go to the main page here, there are in structions for these kits.

[Atomic_Sportsman]

Or we could just read the instructions? Not sure what one you have so here are both links.


First gen lift.

http://www.rubberdowncustoms.ca/forum/showthread.php?t=2621

Second Gen lift.

http://www.rubberdowncustoms.ca/forum/showthread.php?t=7188

[froogle]

Or we could just read the instructions? Not sure what one you have so here are both links.


First gen lift.

http://www.rubberdowncustoms.ca/forum/showthread.php?t=2621

Second Gen lift.

http://www.rubberdowncustoms.ca/forum/showthread.php?t=7188

Phil you're clever, lol.

[Atomic_Sportsman]

Phil you're clever, lol.

You know it.

[RinconMudder]

Phil you're clever, lol.

I guess he ran out of beer..... :tape2:

[stricker76]

Off topic in 16 minutes. New record? LMAO!

[RinconMudder]

Sorry.... but i couldn't resist :biggrin1:

Now :focus:

[Rubberdown]

The washers should both fit if you place them in front of the holes before the bolt slides through rather than putting the 1st one on the bolt before putting the bolt in and putting the second one on the bolt after the bolt is in place. I wont lie to you, its a tight fit to get the washers in place but they "should" bit if placed in place prior to inserting the bolt.

the little bit of play is common, look at my youtube video showing the different from one side of the new XMR to the other with the same lift block being used on both sides.

You should be good to go ;)

[outtyhere]

Thanks ill try that.
Thanks for the welcome guys.
and of course I read the directions first but they do not mention the washers.





[QQUOTE=Rubberdown;186797]The washers should both fit if you place them in front of the holes before the bolt slides through rather than putting the 1st one on the bolt before putting the bolt in and putting the second one on the bolt after the bolt is in place. I wont lie to you, its a tight fit to get the washers in place but they "should" bit if placed in place prior to inserting the bolt.

the little bit of play is common, look at my youtube video showing the different from one side of the new XMR to the other with the same lift block being used on both sides.

You should be good to go ;)[/QUOTE]

[silverz98]

i too never used the washers as i chould not find the place to put them. Paul can u post
a pic on where they go? cause where ithink they should go there no way in hell for them to go on bike

[outtyhere]

I saw the video and I think I have about half the movement of the xmr. Is that still normal? In the video it says the slop or movement is not good. Can someone post a video of a normal amount of movement?

[outtyhere]

I'm hearing alot a front end clanging and banging! Sounds like a quad with shot wheel bearings. My mounts are moving more than a half inch! And they also are twisting slightly back and forth. What should I do, add washers to the inside on the sides of shock?
Also how do I get rid of all this slop I have?

[Rubberdown]

Can you email me a picture or short clip of the problem?

[outtyhere]

What's the email I should send it to?

[Rubberdown]

rubberdowncustoms

@yahoo.ca